fbpx
Login

 

Jump to Forum..

Installation of 6 pin SSM kit

in General Tech Discussion 9 years ago
Hi Guys

Received the 881 280 SSM kit from Lockwood but has no installation instructions.

I read that its plug and play but with an extra wire for each.

Does anyone have the instructions please?

  • Re: Installation of 6 pin SSM kit

    by » 9 years ago

    Hi Reilly,

    It is plug & play for the 6 pin connector. You will just have one open pin slot on each module. make a wire and put one in each module in that open slot. Then run the two wires down to your starter solenoid. You have the larger wires on each side and the small wire in the middle. Take your two new wires that go up to the modules and join them with that small wire in the center of the solenoid. So now you have three wires on that center connection of the solenoid. Now when you turn the engine on these two wires will energise the soft start modules.

    That's it. really simple.

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report

  • Re: Installation of 6 pin SSM kit

    by » 9 years ago

    My understanding (correct me if I'm wrong) is that the soft start only works on one of the modules and that you must start with the other module off. I'm toying with the idea of fitting one and have been told that because I have a left-right-both-start ignition key switch I have to either put in separate mag/module switches or install a push button starter and start with the key switch on the mag/module that the soft start is connected to.
    Can anybody confirm or correct me on this?
    Mike G
      
    Report

  • Re: Installation of 6 pin SSM kit

    by » 9 years ago

    Rotax does have their ignition system setup as an individual switch for ignition #1-2 in the manual, but many owners have it setup on the standard rotary switch. Either seems to work just fine. It seems to be more a personal preference. I have soft start in my Flight Design CT and it's on a rotary switch as are all the FD CT's.

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report

  • Re: Installation of 6 pin SSM kit

    by » 9 years ago

    Hi Mike

    If you fit the after market "Conair Soft Start", it is only fitted to one ignition module and you would start the engine on that ignition circuit only.

    The Rotax one is built into the CDI units themselves and each module has the "Easy start", so you start your engine as normal with both mags on.

    Cheers Mark
      
    Report

  • Re: Installation of 6 pin SSM kit

    by » 9 years ago

    Mark and Roger
    Thank you, I was talking about the aftermarket soft start,I'd forgotten that Rotax now include a soft start.
    Mike
      
    Report
You do not have permissions to reply to this topic.
Related Topics
Title Category Replies
Where to buy 5 year rubber replacement kit 912 / 914 Technical Questions 9
pin cramp for ignition 912 912 / 914 Technical Questions 3
Garmin sensor kit for Rotax 912/915 iS 915iS Technical Questions 3
912 ULS setup in a KitFox II 912 / 914 Technical Questions 2
Pink Coolant - Evans? General Tech Discussion 6
Follow Us

Recent Videos

Safety First!

 

To receive critical-to-safety information on your ROTAX Engine, please subscribe to
ROTAX-OWNER.COM

ROTALK News



ROTALK NEWS Episode 5
Rotax-powered Sling aircraft from The Aircraft Factory, the AVMAP Navigation and engine monitoring system, and the Rotax powered Tucano Experimental and Light-Sport Aircraft.



ROTALK NEWS Episode 4
ROTAX's 915iS-powered Aquila A211 test aircraft, the Scheibe SF-25C Falke (first-ever 912-equipped aircraft!) and ROTAX factory in Gunskirchen, Austria.


ROTALK NEWS Episode 3
Michael Smith's Rotax-Powered Searey Circumnavigation, the amazing Rotax-Powered Lockwood Aircam and Anthony Caere's chimpanzee rescue operations.

Prize Giveaway!


SUBSCRIBE NOW
to automatically enter this years draw!

Login