fbpx
Login

 

Jump to Forum..

912S Reduced Oil Pressure.

in 912iS Technical Questions 13 years ago

  • Re: 912S Reduced Oil Pressure.

    by » 12 years ago

    After control the house had part no 911815 so that means it's for M10x1.

    It's not so easy to measure the the thread and fins out what it is (I think). Bye mistake I mounted a 1/8 NFT and it was possible to do it. So the difference is not big between the two.
    Today I have found an adapter M10x1 to 1/8" NFT, so with that you can mount an 1/8 sensor
      
    Report

  • Re: 912S Reduced Oil Pressure.

    by » 12 years ago

    Anders,

    If you look at the sender, an M10 thread will be straight like a bolt and a relatively fine thread. Yoiu can screw an M10 nut onto it to be sure. A 1/8 NPT will have a coarser thread and will be tapered rather than cylindrical.
      
    Report

  • Re: 912S Reduced Oil Pressure.

    by » 12 years ago

    I give up!
      
    Report

  • Re: 912S Reduced Oil Pressure.

    by » 12 years ago

    Anders,

    Mark had the right info. It is in service letter #SI 912-020R6.

    Look on the BOTTOM of the oil pump housing. Pay no attention to the numbers on the front cover of the housing.

    If you have #911-815 or 911-810 engraved under there, it is threaded for an M10 sensor. If it is #810-809 or 811-809, it is 1/8 NPT.

    Bill.
      
    Report

  • Re: 912S Reduced Oil Pressure.

    by » 12 years ago

    VDO sender 2, 5, 10, 25 bar.
    Resistans +- 4 Ohm

    xxxxxxx10ohm 30ohm 48ohm 65ohm 82ohm 99ohm 116ohm 134ohm 151ohm 168ohm 184ohm
    2 Barxx 0,0 xxx 0,2 xxx 0,4 xxx 0,6 xxx 0,8 xxx 1,0 xxx 1,2 xxx 1,4 xxx 1,6 xxx 1,8 xxx 2,0
    5 Barxx 0,0 xxx 0,5 xxx 1,0 xxx 1,5 xxx 2,0 xxx 2,5 xxx 3,0 xxx 3,5 xxx 4,0 xxxx 4,5 xxxx 5,0
    10 Barxx 0,0 xx 1,0 xxx 2,0 xxx 3,0 xxx 4,0 xxx 5,0 xxx 6,0 xxx 7,0 xxx 8,0 xxx 9,0 xxx 10,0
    25 Barxx 0,0 xx 2,5 xxx 5,0 xxx 7,5 xxx 10,0 xxx 12,5 xxx 15,0 xxx 17,5 xxx 20,0 xxx 22,5 xxx 25,0

    The sender is an variabel resistans
    The 10 Bar Sender has with 0,0 bar oil pressur 10 Ohm.
    And with 2,0 bar oil pressur 48 Ohm and so on.

    Bosse
      
    Report
You do not have permissions to reply to this topic.
Related Topics
Title Category Replies
Plugging Unused Oil Injection Ports 582 Rotax General Tech Discussion 3
Rotax 912 Oil Leak from Rear Exhaust Manifold 912 / 914 Technical Questions 5
912 iS Sport EGT Differences and Coil Problem? 912iS Technical Questions 3
Oil pressure 912 / 914 Technical Questions 2
P2006T，912S ，MAP value be at idle 912 / 914 Technical Questions 2
Follow Us

Recent Videos

Safety First!

 

To receive critical-to-safety information on your ROTAX Engine, please subscribe to
ROTAX-OWNER.COM

ROTALK News



ROTALK NEWS Episode 5
Rotax-powered Sling aircraft from The Aircraft Factory, the AVMAP Navigation and engine monitoring system, and the Rotax powered Tucano Experimental and Light-Sport Aircraft.



ROTALK NEWS Episode 4
ROTAX's 915iS-powered Aquila A211 test aircraft, the Scheibe SF-25C Falke (first-ever 912-equipped aircraft!) and ROTAX factory in Gunskirchen, Austria.


ROTALK NEWS Episode 3
Michael Smith's Rotax-Powered Searey Circumnavigation, the amazing Rotax-Powered Lockwood Aircam and Anthony Caere's chimpanzee rescue operations.

Prize Giveaway!


SUBSCRIBE NOW
to automatically enter this years draw!

Login